PEEK rods have excellent electrical properties and can maintain the electrical stability of the product at high temperatures and frequent temperature changes.
peek 450g rod is is made by PEEK pure resin, it has high impact strength and high toughness.
(brownish gray/earthy yellow) is made from pure polyether ether ketone resin, which is the highest Performing, toughest and most impact resisting of all PEEK grades. It is the unique fact that pure PEEK can be sterilized through convenient sterilization tactics such as, steam, dry heat, ethanol, and y-rays and the raw material used in the preparation of PEEK is responsive to basic food hygiene standards of the European union and U.S froda which makes it very suitable for very common application such in the medical, pharmaceutical, and food processing industries.
PEEK 450Gl30 It is a glass fiber reinforced grade plastic containing 30 percent glass fiber than PEEK has higher rigidity and better creep resistant dimensionally stable parts for the manufacture of structural parts. Up to high temp, for long durations for bearing fixed loads. When used as a sliding part the suitability of PEEK5600GL30 must be considered as the glass fibers in the material damaging the surfaces it comes into contact with.
Through imported PEEK 450ca30 rod for black material containing 30% of carbon fiber reinforcement, and compare with PEEK 450Gl30 has better mechanical properties (the modulus of elasticity, mechanical strength, creep characteristics), more wear-resistant, and then carbon fiber reinforced plastic than PEEK general unreinforced plastic has 3. The heat generated is dissipated from the bearing surface and it was clarified that it was five times faster than the thermal conductivity of a conventional material.
ESD PEEK rod can a protect people or other objects from the danger of voltage discharge. According to static electricity control and permanent discharge of static charges, this kind of plastic can offer high class security to application fields.
AST PEEK rod is derived from PEEK raw material and contains carbon fiber in it. such as carbon black, metal fber, metal powder, permanent antistatic masterbatch and so on to get the function of ACT conductivity and electromagnetic interference shielding.
| NO | DIMENSIONS(MM) | WEIGHT(KG/M) | NO | DIMENSIONS(MM) | WEIGHT(KG/M) | NO | DIMENSIONS(MM) | WEIGHT(KG/M) | |
| 1 | Φ4×1000 | 0.02 | 14 | Φ28×1000 | 0.9 | 16 | Φ90×1000 | 8.93 | |
| 2 | Φ5×1000 | 0.03 | 15 | Φ30×1000 | 1 | 17 | Φ100×1000 | 11.445 | |
| 3 | Φ6×1000 | 0.045 | 16 | Φ35×1000 | 1.4 | 18 | Φ110×1000 | 13.36 | |
| 4 | Φ7×1000 | 0.07 | 17 | Φ40×1000 | 1.73 | 19 | Φ120×1000 | 15.49 | |
| 5 | Φ8×1000 | 0.08 | 18 | Φ45×1000 | 2.18 | 20 | Φ130×1000 | 18.44 | |
| 6 | Φ10×1000 | 0.125 | 19 | Φ50×1000 | 2.72 | 21 | Φ140×1000 | 21.39 | |
| 7 | Φ12×1000 | 0.17 | 20 | Φ55×1000 | 3.27 | 22 | Φ150×1000 | 24.95 | |
| 8 | Φ15×1000 | 0.24 | 21 | Φ60×1000 | 3.7 | 23 | Φ160×1000 | 27.96 | |
| 9 | Φ16×1000 | 0.29 | 22 | Φ65×1000 | 4.64 | 24 | Φ170×1000 | 31.51 |
Comprehensive analysis of material properties, continuous improvement of formula design and process. Strictly control enterprise standards
and qualityinspection process to ensure the ex-factoryiquatity of each product.
PEEK is a high-temperature thermoplastic with a high glass transition temperature (143°C) and melting point (334°C), and a loaded thermal deformation temperature of up to 316°C (30% glass fiber or carbon fiber reinforced grades).
Outer diameter -2mm, inner diameter +2mm
PEEK bars made by a continuous extrusion method typically have lengths of 1000 and 3000 mm, although they can also be trimmed to fit specific customer requirements.
It is more important for PEEK materials to be stored in a dry place and cool environment as this will reduce the chances of absorbing moisture and thus the formation of a deformed structure.
The maintenance of PEEK is relatively simple, but still need to pay attention to the following points in use: The maintenance of PEEK is relatively simple, but still need to pay attention to the following points in use:
Do not use very corrosive solutions such as strong acids or bases to clean PEEK parts to prevent the degradation of the surface of the part as well as its performance.
With PEEK, you can achieve injection molding, milling and turning, etc;
For the manufacturing of complex shape parts, if you need CNC machining, we can also provide appropriate services.
English 
German 
Russian 
Spanish 
French 
Japanese 
Portuguese (Portugal) 
Turkish 
Portuguese (Brazil)